Tyco F3200 Uživatelský manuál Strana 104
- Strana / 284
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
F3200 Installation & Programming Manual Document No: LT0122
Programming System Configuration
Page 7-2 5 July 2001 Issue 2.7
7.1 SYSTEM CONFIGURATION MENU
The System Configuration menu is Option 4 in the Program Data menu (as shown in Fig
6.1.2). It allows programming of the parameters which determine the way the F3200
hardware operates. The menu includes the following:
1 Circuits (AZCs); 2 Zones; 3 Modules; 4 Output Logic; 5 Relay (Supervision); 6 RZDUs and
will also include option 7:Network for a networked system.
Fig 7.1.1A shows the System Configuration menu and its hierarchial structure for V1.10
software, Figure 7.1.1B for V2.00 to V2.08 software and Figure 7.1.1C for V2.09 or later.
The diagram may be used in two ways as follows:
1. When a user needs to change one particular parameter in an existing FIP, Fig's 6.1.2
and 7.1.1 act as a "road map" that show the path required to access that parameter.
2. When initially programming a new FIP, these diagrams may be used as a flowchart.
Working from top to bottom, left to right, on first Fig 6.1.2 and then Fig 7.1.1, the
entire database can be programmed.
This shows that modules should be configured before circuits, zones or relays.
Detail on each is shown in the following sections.
CONFIGURING MODULES
Selecting the modules option causes the LCD to display the modules configured and the
modules present. E.g. Relay 1/2 means that 1 8RM is configured, but 2 are present.
Select: 1 (Zone) to change the number of 8ZMs;
2 (Relay) to change the number of 8RMs;
3 (Display) to change the number of LED Display Bds.
4 (MAF) to enable/disable the MAF board (NDU only)
Acknowledge the warning ("ACK") and then enter the new number of that particular module
to be configured (e.g. press "2", "ENTER" to configure 2 modules).
WARNING
Changing the number of 8 zone or relay modules configured will automatically change
the number of zones or relays allocated in the database. The mapping of zones/relays
to LEDs on an LED Display may well be altered. It needs to be manually checked, and
adjusted if necessary. Refer to Sections 7.3.3 and 7.5.3.
- FIRE INDICATOR PANEL 1
- END USER LIABILITY DISCLAIMER 2
- TABLE OF CONTENTS 3
- AMENDMENTS 5
- CHAPTER 1 7
- INTRODUCTION 7
- 1.1 SCOPE 8
- 1.2 ASSOCIATED DOCUMENTATION 9
- 1.3 PRODUCT HISTORY LOG 10
- 1.5 GLOSSARY OF TERMINOLOGY 13
- Introduction 14
- CHAPTER 2 15
- SYSTEM DESCRIPTION 15
- 2.1 OVERVIEW 16
- System Description 17
- FIG 2.1.1 17
- FIG 2.1.2 18
- F3200 OPERATOR DISPLAY PANEL 18
- FIG 2.1.3 19
- F3200 - SMALL CABINET 19
- 2.2 PHYSICAL STRUCTURE 21
- FIG 2.2.2 23
- 2.3 SYSTEM STRUCTURE 24
- SYSTEM SPECIFICATIONS 29
- CHAPTER 3 29
- 3.1 GENERAL 30
- 3.2 MECHANICAL SPECIFICATIONS 31
- 3.3 ELECTRICAL SPECIFICATIONS 32
- 3.4 INPUT SPECIFICATIONS 36
- 3.5 OUTPUT SPECIFICATIONS 42
- 3.6 CONTROLS 47
- 3.7 DISPLAYS 48
- CHAPTER 4 49
- ORDERING INFORMATION 49
- 4.1 ORDERING INFORMATION 50
- CHAPTER 5 55
- CONFIGURING A FIP 55
- 5.1 GENERAL 56
- 5.2 MODULE CONFIGURATION 56
- 5.4 LINKS ON PCB MODULES 65
- CHAPTER 6 67
- PROGRAMMING 67
- 6.1 INTRODUCTION 68
- FUNCTIONS 78
- DATABASE 79
- PARAMETERS 83
- Programming 102
- CHAPTER 7 103
- 7.3 CONFIGURING ZONES 113
- 7.4 PROGRAMMING OUTPUTS 115
- 7.5 RELAY SUPERVISION 135
- INSTALLATION & WIRING 139
- CHAPTER 8 139
- 8.1 INSTALLATION 140
- 8.2 FIELD WIRING 146
- 8.3 AZC WIRING 148
- Installation & Wiring 149
- FIG 8.3.3 149
- 8.5 WARNING SYSTEM WIRING 153
- FIRE PANEL 155
- 8.6 MODULE RELAY WIRING 158
- 8.7 OPEN COLLECTOR WIRING 160
- 8.9 RDU WIRING 162
- FIG 8.8.1 163
- EXAMPLE OF RDU COMS WIRING 163
- CHAPTER 9 165
- APPLICATIONS 165
- CONFIDENTIAL: 173
- CONTROL MODULE (CCT 1) 173
- SYSTEM/CIRCUIT DIAGRAM 173
- 1.111 PA07261945-1-1A3 173
- CONTROL MODULE (CCT 2) 174
- 1.111 PA07271945-1-2A3 174
- CONTROL MODULE (CCT 3) 175
- 1.111 PA07281945-1-3A3 175
- CONTROL MODULE (CCT 4) 176
- 1.111 PA07281945-1-4A3 176
- 9.2 GAS FLOOD 177
- Applications 183
- FIGURE 9.2.1 183
- GAS FLOOD LOGIC DIAGRAM 183
- FIG 9.2.2 184
- 9.3 SUB FIP MONITORING 189
- (EXPLOSIVE ATMOSPHERES) 192
- * EOL to suit Panel 198
- ZAU401 (Rev 2) 203
- (PA0838) 203
- CHAPTER 10 205
- ALIGNMENT, ADJUSTMENT & 205
- PLACING INTO OPERATION 205
- 10.2 PLACING INTO OPERATION 207
- CHAPTER 11 211
- NETWORK PROGRAMMING 211
- 11.1 INTRODUCTION 212
- 11.2 PROGRAMMING METHODS 214
- TX RLY CTRLS 215
- 11.4 SID CONFIGURATION 222
- 11.6 NET COMMANDS 225
- 11.7 NET FFCIF CONFIGURATION 226
- 11.9 NETWORK LOGIC VARIABLES 230
- 11.10 NET STATUS REFRESH 231
- 11.11 NDU OPERATION 232
- Network Programming 236
- CHAPTER 12 237
- NEW ZEALAND OPERATION 237
- 12.1 GENERAL 238
- 12.3 MANUAL CALLPOINT (MCP) 240
- 12.4 PROGRAMMABLE OPTIONS 241
- 12.5 LOGIC TOKENS 242
- New Zealand Operation 249
- NDU Cabinet 250
- Picture Frame Display Cabinet 251
- FIG 12.8.4 252
- CHAPTER 13 255
- TANDEM LCD MODE 255
- 13.1 TANDEM LCD MODE 256
- APPENDIX A1 257
- APPENDIX A2 262
- Appendix A 265
- Table IV TYCO Detector Range 265
- APPENDIX B 267
- Appendix B 268
- THIS PAGE INTENTIONALLY BLANK 268
- REF: 269
- FUNCTION & LOGIC EQUATION 276
- & LOGIC EQUATIONS 278
- DEISOLATE/RESET EQUATIONS 281
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Tyco F3200
(24 stránky)Rockwell Automation 1391 INSTR/DIGITAL AC SERVO DRIVE manuals
Owner’s manuals and user’s guides for Equipment Rockwell Automation 1391 INSTR/DIGITAL AC SERVO DRIVE.
We providing 1 pdf manuals Rockwell Automation 1391 INSTR/DIGITAL AC SERVO DRIVE for download free by document types: User Manual
Komentáře k této Příručce